Model	Max.Torque (N.m)	Max.Overrunning Speed (r/mm)		Stock Bore Size		A	B(h7)	C
		Inner Race	Outer Race	DiaH7	Keyway
MG300	314	2800	900	19	5x2	63	77	60
MG400	539	2600	800	22	5x2	70	88	67
MG500	1620	2400	800	31.5	7x3	89	108	86
MG600	3140	2100	700	50	12x3.5	95	136	92
MG700	5880	1500	500	70	18x6	127	180	124
MG750	9510	1800	600	85	24x6	153	200	150
MG800	17600	1300	475	110	28x7	158	250	155
MG900	24500	1200	400	135	35x9	165	300	160
MG1000	33800	1200	325	160	38x10	188	370	180
MG1100	78400	350	-	185	45x14	260	470	250
MG1200	95100	300	-	200	45x14	260	500	250
MG1300	176400	250	-	250	56x17.5	280	600	260

 

Model	D	E	F	G	H-M Chip hole	lubricating oil	Oil(cc)
MG300	66	10.4	28.5	13	4xM6xP1.0	M6xP1.0	25
MG400	73	10.7	31.7	16	4xM8xP1.25	M6xP1.0	30
MG500	92	12.3	44.4	16	4xM8xP1.25	M6xP1.0	50
MG600	120	12.8	69.8	16	6xM8xP1.25	M6xP1.0	80
MG700	160	19.8	101.5	20	6xM10xP1.5	M6xP1.0	135
MG750	175	75	110	25	8xM14xP2.0	M8xP1.25	400
MG800	220	77.5	140	25	8xM16xP2.0	M8xP1.25	500
MG900	265	80	170	32	10xM16xP2.0	M8xP1.25	620
MG1000	325	90	200	32	12xM16xP2.0	M8xP1.25	850
MG1100	415	125	260	40	12xM20xP2.5	M12xP1.75	2900
MG1200	440	125	280	45	12xM24xP3.0	M12xP1.75	3000
MG1300	530	130	340	50	12xM30xP3.5	M12xP1.75	3800

Installation and Usage

Model	Tolerance
MG300,MG400	+0, -0.021
MG500,MG600	+0, -2.225
MG700	+0 -0.030
MG750,MG800	+0 -0.035
MG900,MG100	+0 -0.040
MG1100,MG1200,MG1300	+0 -0.046

1.MG Series Clutches consist of MG Series Cam Clutches and oil reservois.See "Installation and Usage" on page 25 for MG series clutches. 2.These clutches are used for backstop applications. 3.Specify right hand (RH) or left hand(LH) drive of inner race viewed from the end marked with the arrow. 4.Prevent oil leakage from the shaft end by using an end plate with packing and sealed washers.Refer to the installation drawing on the right. 5.When attcahing an oil reservoir, be sure to put packing in between the cam clutch end and oil reservoir. Position one of the plugs of the Cam Clutch underneath as a drain and the oil reservoir plug directly above it. Lubrication 1.Oil lubrication is recommended. 2.Do not use greases or lubricants with EP additives.